Move the belt by hand caution: Do not tighten the Belt so much to verify that it is aligned and tracking that the left side of the Sewing Machine correctly. Slide the Sewing Machine Hand Wheel (7b) onto the Main Shaft (32b) of the alĪnd turn it around. Mount the Motor to the underside of the tabletop using the Carriage Bolts (70j), Slot in Tabletop for belt Flat Washers (69j), Spring Washers Bobbin Winder Assembly Figure 7 (68j), and Nuts (67j). Sewing Machine Carriage Bolts (70j), Hand Wheel Flat Washer (69j), Belt (71j) (7b) Spring Washer (68j), Nut (67j) Set Screws (8b) (One on each side of the Pulley) Figure 9 Main Shaft (32b) 5. Place the Oil Pan Magnet (22g) in the lowest portion of the Oil Pan. Tilt the machine back to expose the Oil Pan (1g). Motor Rotation Switch always keep to right Hand Wheel (7b) Figure 5 7. You will need a helper to hold the motor in place while Oil Sight tightening the Nuts (67j) on the Carriage Window (1f) Bolts (70j) in step 5 on the following page. Mounting the Motor Knee Press Oil Pan Magnet Lifter Rod (2g) (22g) note: The Motor is heavy. Seat the Oil Pan (1g) on the Rubber the Single-Needle Sewing Machine (Model Pads and Cushions in the Tabletop 03914) to the Table Stand (Model 03929), not opening. Sewing Machine Hinge Indentations in Tabletop t able Stand and Back of t op (not provided) power Sewing Switch Machine Motor Knee lifting arm for presser Foot Oil Pan (1g) Hinge (1h) Figure 1 Figure 3 The assembly instructions describe mounting 2. Of the machine, depending on the user’s aSSeMBly preference. Volts Alternating Current Always replace a damaged extension V~ cord or have it repaired by a qualified Amperes el Make sure the extension cord is properly wired and in good electrical condition. If you are using an extension cord outdoors, make sure it is marked with the Canadian Standards Association suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
(See Symbology t able a.) Double Insulated 6. Check with a qualified electrician (See 3-prong plug and Outlet.) if you are in doubt as to whether 3. The green wire in the cord must and death FrOM incOrrect be the only wire connected to the tool’s grOunding wire grounding system and must never be cOnnectiOn: attached to an electrically “live” terminal. The grounding prong in the plug is grOunding connected through the green wire inside tO preVent the cord to the grounding system in the electric ShOcK tool. During operation, never place your head, awg. cord with up to 10 amps capability (up to 50 feet), with wire size rated at 18 4. Never leave the machine running and This tool requires use of an extension unattended. Otherwise, the take-up cover while the machine is extension cord could melt and catch fire, operating. Do not place your fingers into the thread tool without heating up. Watch what you are doing, applications for which this product was use common sense. Be sure not attempt to force a small product the switch is in the Off position when not or attachment to do the work of a in use and before plugging in. Always lock up tools and the machine work surface before keep out of reach of children. Feed Type Link style needle feed Sewing Directions Forward and reverse feed 3 Machine Dimensions 20- / ” L x 10” H 4 - 2 Screwdrivers- 3 Bobbins- Small lubricating bottle with tip- Spare needles (size 90/14) Accessories - Power Switch Table Stand Kit Table S
Forward and reverse motor spool sdcf755m134lf1 manual#
SpeciFicatiOnS Machine Type Heavy duty, industrial sewing machine high speed, single needle-lock stitch Drive V-belt driven (size 41 replacement belt) Action Foot pedal operation, along with a knee and manual lifting arm for presser foot. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. © ® Copyright 2005 by Harbor Freight Tools. Failure to do so can result in serious injury.
Single needle induStrial Sewing Machine Model 3914 Set up and Operating inStructiOnS Visit our website at: read this material before using this product.